Showing posts with label how to. Show all posts
Showing posts with label how to. Show all posts

Thursday, December 10, 2015

Quick and easy Bottlecap refrigerator magnets

Quick and easy Bottlecap refrigerator magnets 

So for this project you will need an assortment of bottle caps from either microbrews or smallbatch soda pop. Preferably selecting bottle caps with interesting designs. You will also need a hot glue gun, magnets that will fit inside the bottlecap, and something to use as a spacer such as a piece of Styrofoam, sliced wood dowel or piece of plastic.
 Place your bottle caps upside down on the work surface as shown in the photos below. Hot glue your spacer inside the bottlecap. Make sure your spacer sit evenly with the edge of the bottlecap in thickness. If you do not have a spacer fill the bottlecap with hot glue and let cool. The reason for letting the glue cool is that if you place the magnet on the hot glue while it is still hot the magnet will sink out of sight.
You will want the magnet to set above the edge of the bottlecap so if the bottlecap magnet gets moved it is less likely to scratch the refrigerator. If you're concerned about scratching the refrigerator apply a small bead of hot glue around the sharp edges. Another option is to buy a cookie sheet from the dollar store and use it to display your magnets on.

 Once the glue has cooled the magnet is finished and ready to use or give as a gift. It is also a great way to keep track of all the great beverages that you drink or just to collect bottle caps.
The following is a short video on how to make the magnets.

Tuesday, April 30, 2013

DIY solar lighted stepping stones


How to make solar lighted stepping stones.


[note:  The glass used in this project is not safety glass and can break under certain conditions. If rocks or other objects strike the glass with sufficient force it is possible for the glass to break creating sharp edges and unsafe conditions. The author of this blog is not responsible for misuse or persons not taking do care and it's information is intended for conceptual purposes only.]
To make your mold  cut off the bottom of a 5 gallon plastic bucket. (note: do not throw away the upper half as it can be used to be used to protect plants and other things, but that is for another blog.) Using a ruler or tri-square cut 3 inches off the bottom of the bucket. This should give you a mold that is 2 1/2 inches to 3 inches deep. Steppingstones need to be at least 2 inches thick in order to support your weight. Be sure and spray a mold release such as vegetable oil on the inside of your mold.(note; do not spray the glass jar as you want the cement stick to the jar. you may even want to sand the outside edges to make the cement stick better, but do not sand the bottom.) Be sure and select jars that are wide-mouth and large enough and deep enough to fit your solar light inside of before you pour the cement.
 Once your cement is poured be sure and tap the edges to remove air bubbles. Wipe any cement sticking to the edges of the lid, as you'll want to remove the lid later. Let your cement set overnight to cure and your stones should be easily removed from the mold. Be sure and take care as the cement will not be completely cured as yet and the stones are still fragile. If it does not easily remove from the mold, then allow the cement to cure a little longer. Set in a tub of water or keep damp inside a plastic bag for at least 5 to 6 days to finish curing. The slower cement cures, the stronger the cement.

I used these glass ball solar lights. The LED is mounted on top of the solar cell, which makes them perfect for this project. using gloves, safety glasses and a screwdriver I carefully pry off the glass ball. Work the screwdriver down the edges loosening any glue and then twisting the screwdriver to pry the glass ball loose. Discard or save for another project the glass ball and tube stand.
                                         Remove your lid from the glass jar. Using a Styrofoam ball I cut off the bottom of the ball to create a flat surface and cut a hole in the center of the ball to mount the solar light in. (Any piece of Styrofoam will work as long as it holds the solar light up right.) I used a low temp hot glue gun as I wanted to be able to remove the solar light if I needed to make repairs. I glue the flat bottom to the inside of the jar lid and tack the solar light to the Styrofoam ball to hold it in place while it is being assembled.            
Once you have your stone assembled, you are ready to set the stone in the ground. Select a site that is free of rocks and other debris. Rocks and other debris could score the glass causing it to break or cause uneven pressure on the stone itself and break the steppingstone. Digg a depression large enough for the stone itself (about a 1/2 inch deep) and a small depression slightly smaller than the diameter of the jar and slightly deeper than the depth of your jar in the center to accommodate the glass jar. Be sure and do not set the stone too deep as you do not want the stone to become buried. Move the stone around slightly and tamp the soil firmly making sure the stone is set firmly and does not rock back and forth. Uneven pressure on the stone could cause it to break, so it is very important that the stone is set firmly before you put your full weight on the stone.
So there you have it, solar lighted steppingstones to light your path or just add accent to your garden or landscaping.
***********************
If solar lights are not your thing or you just want to add color to your stones then a low voltage system may be what you want. The diagram below shows how you might use wine bottles cut in half to make your lighted stepping stones.



You could also use a light set like this and clear bottles to get colored lights. ( note: make sure lights are rated for being buried or exposed to moisture )

Adding marbles or tile or other colorful items is simple. Just lay them in the bottom of the mold and pour cement carefully on top. Keys, tile, marbles and even broken dishes can be used in a mosaic pattern. After it semi_sets use a toothbrush or nylon pot scrubber to clear off cement and reveal mosaic.If I was to use marble or other items again I would try to keep them away from the edges. I did not do so in the one shown above and I got too close to the edges which created weak spots and ruff edges. After it has fully cured I will coat with a clear seal, which will give it a polished look.

Be sure and check out our other blogs and website 


http://patterns44.blogspot.com/


Saturday, June 30, 2012

Homemade aluminum plant tags



Homemade aluminum plant tags

 

So you may have wondered why I didn't use aluminum cans?



Aluminum cans are hard to work with and leave sharp edges. That's not to say you can't use them, just be more careful. If you use an aluminum can be sure to bend the edges over to eliminate sharp edges. (note: If you can get cut on a piece of paper, you can get cut on one of these tags.) Sorry in this day and age with all the idiots out there, I have to put disclaimers on everything.
The aluminum I use is easy to work with and it's an aluminum that doesn't normally get recycled. It is not as rigid as aluminum cans, but still holds it's shape.
The plant tags will last for a long time. I have some tags that are over 10 years old. The following is an example of what I put on my tags.

  • Name of plant
  • date planted (moon phases and or planetary alignment )
  • where purchased (note many stores guarantee plants)
  • original location (if moved or propagated)
  • herb, fruit,vegetable
Or

  • Name of plant
  • Ref number
Then have a catalog with the reference number and all the details about the plant that you could not include on the tag.

Other ideas are to use the tags on gifts, as Christmas ornaments, luggage tags, or anywhere you need a nice tag.

Sunday, June 24, 2012

DIY floating solar lights and battery yard lights ideas

Floating solar lights and yard accent lights

These are inexpensive ways to light up your yard.


Note: glass, plastic, or even metal coffee cans with holes can be used to make yard accent lights.

Make your own stepping stone mold

Stepping stones

Make your own stepping stone mold.
Note: things not mention in video.
  1. 1.Stones take up to 5 or 6 days to fully cure and be strong enough to walk on.
  2. 2. When setting stones in place it is very important to set them on smooth level ground. any uneven points or rocks under the stone could break or crack the stone.